CyberPower RMCARD202TAA User Manual

User’s Manual Remote Management Card RMCARD202 Intelligent Remote Management Card allows a UPS system to be managed, monitored, and configured V

CyberPower Remote Management System 8 WEB INTERFACE Login Account There are two user account types. - Administrator (default username : cyber ;

CyberPower Remote Management System 9 [UPS->status] Displays the basic information about the current UPS status, and the items that are auto refr

CyberPower Remote Management System 10 Working Frequency The output frequency rating(Hz) of the UPS. Power Rating The Volt-Amp rating of the UPS.

CyberPower Remote Management System 11 Recharged Capacity When the utility power restores, the UPS will start to recharge after the s

CyberPower Remote Management System 12 [UPS->Master Switch] Switches the output power of the UPS to be on or off. Items Definition Reboot UPS

CyberPower Remote Management System 13 of the battery, including the results and date of the last battery test. Click the Initiate button to begin a

CyberPower Remote Management System 14 effect and when to perform it. [One Time]: The user may set a specific date and time for the UPS shutdown. [

CyberPower Remote Management System 15 Items Definition Event Logs Clear All Clear the existing event logs. The Number of Events The number

CyberPower Remote Management System 16 • Click “Apply” Change Viewer account: • Select “Allow Access” to enable the Viewer account • Enter the User

CyberPower Remote Management System 17 - SMS: Send a short message to a specific mobile phone number. (An available SMS service provider is needed)

CyberPower Remote Management System 2 TABLE OF CONTENTS Introduction………………………………………………………………………1 Installation Guide………………………………………………………………..3 Web I

CyberPower Remote Management System 18 [System-> Notifications->SMS Service] Short Message Service (SMS) is a communication service used by m

CyberPower Remote Management System 19 the Agent/Client sends a notification to the SMS provider. [System-> Notifications->SMS Recipient

CyberPower Remote Management System 20 Forbidden No GETS or SETS. [System-> Network Service->Telnet Service] Selects Enable to allow acc

CyberPower Remote Management System 21 RESETReset to Default Setting / Recover from a Lost Password To reset the CyberPower Remote Management Card t

CyberPower Remote Management System 22 ftp > bin ftp > put cpssnmpfw_XXX.bin 6. Upgrade complete , type ftp > quit 7. The system will reb

CyberPower Remote Management System 23 Trouble Shooting Problem Solution Unable to configure the Management Card by method1 or method2 1. Check th

CyberPower Remote Management System 24 Appendix 1 IP Address Settings for the CyberPower Remote Management Card Overview All devices on a computer

CyberPower Remote Management System 25 If the response is shown as below, the IP address is in use. Try another IP address until an available addre

1 INTRODUCTION Overview The CyberPower Remote Management Card allows for remote monitoring and control of a UPS attached to a network. After install

CyberPower Remote Management System 2 Application: Unpacking Inspect the Remote Management Card upon receipt. The package should co

CyberPower Remote Management System 3 INSTALLATION GUIDE Step 1. Hardware Installation Internal smart slot Remote Management Card (RMCARD202) 1.

CyberPower Remote Management System 4 Definitions for LED Indicators Link LED color Condition Off The Remote Management Card is not c

CyberPower Remote Management System 5 Figure 1. The main window of the “Power Device Network Utility” program. 4. Select the Remote Manag

CyberPower Remote Management System 6 Figure 3. The authentication window. 8. If IP address is successfully set, you will see a message tha

CyberPower Remote Management System 7 Method 2: Using a command prompt 1. Obtain the MAC address from the label on the Remote Management Card rear p