CyberPower CPS1000AVR User Manual

Browse online or download User Manual for Uninterruptible power supplies (UPSs) CyberPower CPS1000AVR. CyberPower CP1000AVRLCD uninterruptible power supply (UPS)

  • Download
  • Add to my manuals
  • Print
  • Page
    / 1
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
12
3
4
7
8
Automatic Voltage Regulators
increase low or decrease high voltage to a computer
safe 110/120 volts. The AVR automatically provides
battery back-up power if line voltage drops below 90
volts or exceeds 140 volts.
AVR
INCONSISTENT
UTILITY POWER
CONSISTENT
SAFE POWER
Min
V
ESTIMATE RUN_TIMEINPUT
LOAD CAPACITY
BATT. CAPACITY
OUTPUT
BATTERY
A.V.R
FAULT
NORMALNORMAL
SILENT
OVER
LOAD
100
IN OUT
5
6
9
10
11
12
UNPACKING
Inspect the UPS upon receipt. The box should contain the following:
(1) UPS unit; (1) User’s manual; (1) PowerPanel
®
Personal Edition software CD; (1) USB device cable; (1) Telephone
cable; (1) Warranty registration card; (1) Coaxial Cable
OVERVIEW
The CP850AVRLCD / CP1000AVRLCD provides automatic voltage regulation for
inconsistent utility power. The CP850AVRLCD / CP1000AVRLCD features 890
/1080 Joules of surge protection, and provides battery backup during power
outages. The CP850AVRLCD / CP1000AVRLCD ensures consistent power to your
computer system and its included software will automatically save your open files
and shutdown your computer system during a utility power loss.
AUTOMATIC VOLTAGE REGULATOR
The CP850AVRLCD / CP1000AVRLCD stabilizes inconsistent utility
power. The incoming utility power may be damaging to important data
files, but with Automatic Voltage Regulation, the computer will not
experience damaging voltage levels. An Automatic Voltage Regulator
automatically increases low or decreases high voltage to a consistent,
computer safe 110v/120v. The unit’s powerful sealed lead-acid
batteries will provide power only if the incoming voltage drops below
90v or increases above 140v.
HARDWARE INSTALLATION GUIDE
1.Your new UPS may be used immediately upon receipt. However, recharging the batteries
for at least 16 hours is recommended to ensure that the battery’s maximum charge capacity
is achieved. A loss of charge may occur during shipping and storage. To recharge the
batteries, simply leave the unit plugged into an AC outlet. The unit will charge in both the
ON as well as the OFF position.
2.With the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage
device (Zip drive, Jazz drive, Tape drive, etc…) into the battery power supplied outlets. Plug your peripheral
equipment (printer, scanner, speakers) into the full-time surge protection outlets. DO NOT plug a laser printer, paper
shredder, copier, space heater, vacuum or other large electrical device into the UPS. The power demands of
these devices will overload and possibly damage the unit.
3. To surge protect a network connection, connect a network cable from the wall jack outlet to the IN jack of the UPS.
Then connect a network cable from the OUT jack on the UPS to the network device.
4.Plug the UPS into a 2 pole, 3 wire grounding receptacle (wall outlet). Make sure the wall branch outlet is protected by
a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. refrigerator, copier, etc…).
The warranty prohibits the use of extension cords, outlet strips, and surge strips.
5.Press the power switch to turn on the unit. The unit will beep twice and the power on indicator will illuminate.
6.If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the
UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make
sure the circuit breaker is depressed and then turn the UPS on.
7.To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
8.To store your UPS for an extended period, cover it and store with the battery fully charged. While in storage recharge
the battery every three months to ensure battery life.
SOFTWARE INSTALLATION GUIDE
Windows Users
When you first get a new CyberPower UPS, you'll need to install some software on your computer to control your UPS
and begin using it.
Installing PowerPanel
®
Personal Edition
1. Place the CD in your CD drive and wait for the setup wizard to begin. If the wizard does not begin, go to your CD drive
in "My Computer" and open the "PowerPanel
®
PE " folder and double click "Setup.exe".
2. Follow the instructions on your screen and complete the installation. The default settings offered by the installation
wizard are acceptable for most users and can be changed at any time if necessary.
3. After the setup is complete plug the USB cord from your CyberPower UPS to an available USB port on your computer.
4. You are now ready to begin using the PowerPanel
®
Personal Edition software.
Mac Users
When you first get a new CyberPower UPS, you'll need to configure the Mac UPS function to control your UPS and
begin using it.
Configuring the "Energy Saver" UPS Function
1. Plug the USB cord from your CyberPower UPS to an available USB port on your computer..
2. Go to "System Preferences" and open the "Energy Saver" control panel.
3. Select settings for "UPS".
You are now ready to configure the settings for the UPS.
CP850AVRLCD / CP1000AVRLCD
User’s Manual
K01-0000023-00
(SAVE THESE INSTRUCTIONS)
This manual contains important safety instructions. Please read and follow all instructions carefully during installation
and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free
of conductive contaminants. (Please see specifications for acceptable temperature and humidity range).
CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user
serviceable parts are inside except the battery.
CAUTION! Some components can be energized by the battery when unit is unplugged.
CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an
outlet that is not grounded. If you need to de-energize this equipment, turn off and unplug the unit.
CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the
battery or installing a computer component.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life
support or medical applications. DO NOT use in any circumstance that would affect operation or safety of any life
support equipment or with any medical applications or patient care.
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an
aquarium. Condensation from the aquarium can cause the unit to short out.
DO NOT USE WITH LASER PRINTERS! The power demands of these devices will overload and possibly damage the
unit.
DESCRIPTION
1 Power Switch
Used as the master on/off switch for equipment connected to the battery
power supplied outlets.
2 Power On Indicator
This LED is under the power switch. It illuminates when the utility condition
is normal and the UPS outlets are providing power, free of surges and
spikes.
3 LCD Module Display.
High resolution and intelligent LCD display shows all the UPS information
with icons and messages. For more information please check the
“Definitions for Illuminated LCD Indicators” section.
4 LCD Display Toggle/Selected Switch
The switch can be used to select the LCD display contents including Input Voltage, Output Voltage and Estimated Run
Time. The toggle frequency is set to one time per second. Holding the switch for more than two seconds while running
on battery will silence the buzzer.
5 Battery and Surge Protected Outlets
The unit has five battery powered/surge protected outlets for connected equipment and ensures temporary uninterrupted
operation of your equipment during a power failure.
6 Full-Time Surge Protection Outlets
The unit has four always on surge suppression outlets.
7 Electrical Wiring Fault Indicator
This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or
reversed wiring. If this is illuminated, user is advised to disconnect all electrical equipment from the outlet and have an
electrician check to ensure the outlet is properly wired. The unit will not provide surge protection without being plugged
into a grounded and properly wired wall outlet.
8 Communication Protection Ports
Communication protection ports will protect any standard modem, fax , telephone line, broadband network or Ethernet
connection.
9 Circuit Breaker
Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.
10 Serial/USB Ports to PC
The USB and serial port allow communication from the UPS to the computer. The UPS communicates its status to the
PowerPanel
®
Personal Edition software when connected with a USB port. The serial port is only used with third party
UPS software such as the Microsoft UPS Power Option of Windows 2000, XP, and Vista. For information on configuring
and using the serial port and the Microsoft UPS Power Option or for information regarding ordering a standard serial
cable, please contact technical support at [email protected].
Note: The serial port and USB port cannot be used to control two computers concurrently. Only one port will function at
a time.
11 Coax/Cable/DSS Surge Protection
The Coax/Cable/DSS surge protection ports will protect any cable modem, CATV converter, or DSS receiver.
12 Input Power Cord
Connect the unit into an AC outlet.
CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the
battery under the supervision of personnel knowledgeable of batteries and their precautions.
CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.
CAUTION! The battery may present a risk of electrical shock. Do not dispose of battery in a fire as it may explode.
Follow all local ordinances regarding proper disposal of batteries. Almost any retailer that sells lead-acid batteries
collects used batteries for recycling, as required by most state laws.
CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to skin and eyes and may be toxic.
CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following precautions
before replacing the battery:
1.Remove all watches, rings or other metal objects.
2.Only use tools with insulated handles.
3.Do not lay tools or metal parts on top of battery or any terminals.
4.Wear rubber gloves and boots.
5.Determine if the battery is inadvertently grounded. If grounded, remove the source of ground. CONTACT WITH A
GROUNDED BATTERY
CAN RESULT IN ELECTRICAL SHOCK!
Model CP850AVRLCD CP1000AVRLCD
Capacity 850VA / 510W 1000VA / 600W
Input Voltage on Utility 90V to 140V
Input Frequency 60 Hz ± 3 Hz
On-Battery Output Voltage 120Vac ± 5%
Transfer Time 4ms Typical
Max. Load for UPS Outlets 850VA / 510W 1000VA / 600W
Max. Load for Full-Time 
Surge Protection outlets (9 Outlets)
12 Amps
On-Battery Output Wave Form Simulated Sine Wave Form
Operating Temperature + 32°F to 95° F / 0° C to 35° C
Operating Relative Humidity 0 to 95% NON-CONDENSING
Size (L x W x H)
10.24" x 4.33" x 8.70"
26.0 x 11.0 x 22.6cm
Net Weight 15.8 lbs 16.7 lbs
Typical Battery Recharge Time 8 hours typical from total discharge
Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles
Battery Type Spill-proof, Maintenance-free, sealed lead-acid
Safety Approvals UL1778(UPS), cUL107., FCC/DoC Class B
Model iMac G4
Desktop PC  Desktop PC Desktop PC  Desktop PC
with 17" LCD Monitor with 19" LCD Monitor with 21" LCD Monitor with CRT Monitor
CP850AVRLCD 87 minutes 49 minutes 42 minutes 34 minutes 32 minutes
CP1000AVRLCD 89 minutes 50 minutes 42 minutes 35 minutes 34 minutes
IMPORTANT SAFETY WARNINGS
INSTALLING YOUR UPS SYSTEM
BASIC OPERATION
TROUBLE SHOOTING
DEFINITIONS FOR ILLUMINATED LED INDICATORS
Limited Warranty and Connected Equipment Guarantee
TECHNICAL SPECIFICATIONS
1. Turn off and unplug all connected equipment.
2. Turn the UPS off and unplug it from the AC power source.
3. Turn the UPS upside down.
4. Remove the retaining screw.
5. Slide the battery compartment cover completely off of the unit.
6. Remove the batteries from the compartment.
7. Disconnect the battery wires from the batteries.
8. Install the replacement batteries by connecting the red wire
and black wire to the same color wires from the battery pack.
9. Put the batteries back into the compartment.
10. Slide back the battery compartment cover and tighten the
retaining screw.
11. Recharge the UPS for 8-16 hours to fully charge the battery.
The LCD display indicates a variety
of UPS operational conditions. All
descriptions apply when the UPS is
plugged into an AC outlet and turned
on or when the UPS is on battery.
INPUT voltage meter: This meter measures the AC voltage that the UPS
system is receiving from the utility wall outlet. The UPS is designed, through
the use of automatic voltage regulation, to continuously supply connected
equipment with stable, 110/120 output voltage. In the event of a complete
power loss, severe brownout, or over-voltage, the UPS relies on its internal
battery to supply consistent 110/120 output voltage. The INPUT voltage meter
can be used as a diagnostic tool to identify poor-quality input power.
OUTPUT voltage meter: This meter measures, in real time, the AC voltage
that the UPS system is providing to the computer, such as normal line mode,
AVR mode, and battery back up mode.
Note: The OUTPUT voltage meter shows the status of the battery back up
outlets.
ESTIMATE RUN TIME: This displays the run time estimate of the UPS with
the current battery capacity and load.
NORMAL icon: This icon appears when the UPS is working under normal conditions.
BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps
followed by a pause) to indicate the UPS is operating from its internal batteries. During a prolonged brownout or
blackout, the alarm will sound continuously (and the BATT.CAPACITY meter shows one 20% capacity segment shaded)
to indicate the UPS’s batteries are nearly out of power. You should save files and turn off your equipment immediately.
AVR (Automatic Voltage Regulator) icon: This icon appears whenever your UPS is automatically correcting too low or
too high AC line voltage without using battery power. This is a normal, automatic operation of your UPS, and no action is
required on your part.
SILENT MODE icon:This icon appears whenever the UPS is in silent mode. The buzzer does not beep during silent
mode until the battery reaches low capacity.
OVER LOAD icon: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To
clear the overload, unplug some of your equipment from the battery-supplied outlets until the icon turns off and the alarm
stops.
FAULT icon: This icon appears if there is a problem with the UPS. Contact CyberPower Systems at
[email protected] for further help and support.
BATT. CAPACITY meter: This meter displays the approximate charge level (in 20% increments) of the UPS’s internal
battery. During a blackout or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the
charge level decreases.
LOAD CAPACITY meter: This meter displays the approximate output load level (in 20% increments) of the UPS’s
battery outlets.
Alarm
Condition
On Off Off Normal
On On/Off
2 beeps
per 30 seconds
On On/Off Rapid beeps
On On/Off Long beeps
On On None
POWER
ON
WIRING
FAULT
Utility failure—The UPS is providing battery power to the battery power-
supplied outlets.
Utility failure—The UPS is providing battery power.The rapid beeps mean
that the battery will run out of charge within a few minutes.
Battery overload—Occurs in the battery power-supplied outlets. Turn off
the UPS and unplug at least one piece of equipment from the UPS. Wait
10 seconds, press the circuit breaker reset button, then turn the UPS on.
Electrical wiring fault—This means there’s a wiring problem within the
utility AC power outlet. A wiring problem could be a bad ground, missed
ground, or reversed wiring. You should disconnect all equipment from
the outlet and have it checked by an electrician.
REPLACING THE BATTERY
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
REMINDER: Batteries are consider HAZARDOUS WASTE and must be disposed
of properly. Almost any retailer that sells lead-acid batteries collects used batteries for recycling, as required by most
state laws.
Additional troubleshooting information can be found at
www.cyberpowersystems.com/support.htm
Problem Possible Cause Solution
Full-time surge protection outlets
stop providing power to equipment.
Circuit breaker button is projecting
from the side of the unit.
Circuit breaker has
tripped due to an
overload.
Turn the UPS off and unplug at least one piece of equipment.
Wait 10 seconds, reset the circuit breaker by depressing the
button, and then turn the UPS on.
The UPS does not perform
expected runtime.
Recharge the battery by leaving the UPS plugged in.
Contact CyberPower Systems about replacement batteries at
Battery is slightly worn out.
Battery not fully charged.
The UPS will not turn on.
The unit failed a self test.
Turn the UPS off. Wait 10 seconds and then turn the UPS on.
The unit is not connected to an
AC outlet.
The unit must be connected to a 110/120v 60Hz outlet.
The battery is worn out.
Contact CyberPower Systems about replacement batteries at
Mechanical problem.
Contact CyberPower Systems at
Power Panel
®
Personal Edition is
inactive (all icons are gray).
The USB cable is not
connected.
Connect the USB cable to the UPS unit and an open USB port
on the back of the computer. You must use the cable that
came with the unit.
The USB cable is connected
to the wrong port.
Check the back of the computer for an additional USB port.
Move the cable to this port.
The unit is not providing
battery power.
Shutdown your computer and turn the UPS off. Wait 10
seconds and turn the UPS back on. This should reset the unit.
EXPECTED RUNTIME IN MINUTES
(Due to the differences in computer components, the runtime will vary.)
Read the following terms and conditions carefully before using the CyberPower CP850AVRLCD / CP1000AVRLCD (the
“Product”). By using the Product you consent to be bound by and become a party to the terms and conditions of this
Limited Warranty and Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to
the terms and conditions of this Warranty, you should return the Product for a full refund prior to using it.
Who is Providing this Warranty?
CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.
What Does This Warranty Cover?
This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also
covers equipment that was connected to the Product and damaged because of the failure of the Product.
What is the Period of Coverage?
This warranty covers the Product for three years and connected equipment for as long as you own the Product.
Who Is Covered?
This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.
How Do You Get Service?
1.Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 5555 12th Ave. E., STE 110, Shakopee,
MN 55379 or send us an e-mail message at [email protected] for instructions.
2.When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment.
Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial
Customer and Request a Claim Number.
3.You must provide a purchase receipt (or other proof of the original purchase) and provide a description of the defect.
4.Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost
estimate for the damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the
Claim Number on the shipping label or include it with the product. You must prepay all shipping costs, you are
responsible for packaging and shipment, and you must pay the cost of the repair estimate.
How Long Do I Have To Make A Claim?
All claims must be made within ten days of the occurrence.
What Will We Do To Correct Problems?
CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or,
if CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time,
CyberPower will refund to you the full purchase price you paid for the Product (purchase receipt showing price paid is
required).
If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your
claim for the connected equipment. We will repair or replace the equipment that was damaged because of the failure of
our Product or pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the
damage. We will use Orion Blue Book, or another a third-party valuation guide, or eBay, craigslist, or other source to
establish that amount. Our liability is limited to CP850AVRLCD - $250,000; CP1000AVRLCD-$350,000.
Who Pays For Shipping?
We pay when we send items to you; you pay when you send items to us.
What Are Some Things This Warranty Does Not Cover?
1.This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the
Product or any data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of
software.
2.This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of
the Product or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been
improper operation or maintenance, or use with items not designed or intended for use with the Product, such as laser
printers, appliances, aquariums, medical or life support devices, etc.
.
What Other Limitations Apply?
1.This Warranty does not apply unless the Product and the equipment that was connected to it were connected to
properly wired and grounded outlets (including compliance with electrical and safety codes of the most current
electrical code), without the use of any adapters or other connectors.
2.The Product must have been plugged directly into the power source and the equipment connected to the Product must
be directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords,
another Product or device similar to the Product, surge suppressor, or power tap. Any such installation voids the
Limited Warranty.
3.The Product and equipment connected to it must have been used properly in a suitable and proper environment and in
conformance with any license, instruction manual, or warnings provided with the Product and the equipment
connected to it.
4.The Product must have been used at all times within the limitations on the Product’s VA capacity.
What are the Limitations?
The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.
The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or
impulses from lightning or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has
occurred, the occurrence will be deemed outside the rated capabilities of the Product and the Limited Warranty is void.
CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following:
1.Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
2.Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and
code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on standard
telephone land lines, PBX telephone equipment lines or Base 10T Ethernet lines, when properly installed and
connected. (This exclusion applies, for example, to fluctuations in data transmission or reception, by CATV or RF
transmission or fluctuations, or by transients in such transmission.)
3.Damage from any circumstance described as excluded above with respect to the Product.
4.Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of
either the product or the Connected Equipment.
5.CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment
Guarantee. CyberPower excludes any liability for direct, indirect, special, incidental or consequential damages,
whether for damage to or loss of property [EXCEPT FOR (AND ONLY FOR) the specific limited agreement of
CyberPower to provide certain warranty benefits regarding "Connected Equipment" under this Warranty], loss of
profits, business interruption, or loss of information or data. NOTE: Some States or Provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
6.The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in
hazardous environments requiring fail-safe performance, or for use in any circumstance in which the failure of the
Product could lead directly to death, personal injury, or severe physical or property damage, or that would affect
operation or safety of any medical or life support device (collectively, "High Risk Activities"). CyberPower expressly
disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums. CyberPower does not
authorize use of any Product in any High Risk Activities or with Aquariums. ANY SUCH USE IS IMPROPER AND IS A
MISUSE OF THE PRODUCT.
What is the Fine Print?
The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.
CyberPower is the warrantor under this Limited Warranty.
For further information please feel free to contact CyberPower at Cyber Power Systems (USA), Inc. 5555 12th Ave E.,
STE 110, Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at
TO REPLACE THE BATTERY
PLUG IN
Page view 0
1

Summary of Contents

Page 1 - User’s Manual

123478Automatic Voltage Regulatorsincrease low or decrease high voltage to a computer safe 110/120 volts. The AVR automatically provides battery back-

Comments to this Manuals

No comments