CyberPower RMCARD202 User Manual

User’s Manual Remote Management Card RMCARD202/RMCARD203 RMCARD302/RMCARD303 Intelligent Remote Management Card allows a UPS system/environment s

CyberPower Remote Management System 8 WEB INTERFACE Login Account There are two types of user account: - Administrator (default username: cyber;

CyberPower Remote Management System 9 Humidity The current humidity of the environment in a graph. Envir Data Name The name of the environment s

CyberPower Remote Management System 10 Remaining Runtime How long the UPS can support its load under battery mode. System Temperature

CyberPower Remote Management System 11 [UPS->Configuration] Configure the parameters of the UPS. Item Definition Supplied Power Volta

CyberPower Remote Management System 12 Otherwise the UPS will stop supplying output power. Check Volt Only: Only if the utility voltage is in the

CyberPower Remote Management System 13 enabled, the UPS can be turned on without input power. Audible Alarm If this option is enabled, the UPS

CyberPower Remote Management System 14 [UPS->Master Switch] Switch the output power of the UPS to be on or off. Item Definition Reboot UPS Tur

CyberPower Remote Management System 15 user to verify the battery conditions and provides information about the battery, including the results and d

CyberPower Remote Management System 16 [One Time]: The user may set a specific date and time for the UPS shutdown. [Per Day]: Set a specific time of

CyberPower Remote Management System 17 Maximum The highest humidity as well as the time of occurrence detected by the environment sensor.

CyberPower Remote Management System TABLE OF CONTENTS Introduction ...

CyberPower Remote Management System 18 [Logs->Event Logs] Display the list of events and a brief description of each event along with the date a

CyberPower Remote Management System 19 Event Logs Clear All Clear the existing event logs. The Number of Events The number of existing event lo

CyberPower Remote Management System 20 Change Viewer account: • Select “Allow Access” to enable the Viewer account • Enter the User Name • Set the M

CyberPower Remote Management System 21 - IPv6 Interface: Displays the current IPv6 address. - IPv6 Gateway: Displays the current IPv6 gateway. -

CyberPower Remote Management System 22 User Name The name to identify SNMPv3 user. The field must be 1 to 31 characters length. Authentucation Pas

CyberPower Remote Management System 23 - Log: Record the event in the “Event Logs”. - E-mail: Send an email to a specific user (An available SMTP

CyberPower Remote Management System 24 Service provider accepts HTTP GET This specification from the SMS provider is required before using the HTTP

CyberPower Remote Management System 25 [System->About] Display vital information for the Remote Management Card. Item Definition Model Name M

CyberPower Remote Management System 26 Reset to Default Setting / Recover from a Lost Password To reset the CyberPower Remote Management Card to it

CyberPower Remote Management System 27 Firmware Upgrade By upgrading the Firmware, you can obtain both the new features and updates/improvements to

1 INTRODUCTION Overview The CyberPower Remote Management Card allows for remote monitoring and controlling of a UPS attached to a network. After ins

CyberPower Remote Management System 28 Trouble Shooting Problem Solution Unable to configure the Management Card by method 1 or method 2 in user’s

CyberPower Remote Management System 29 Appendix 1. IP Address Settings for CyberPower Remote Management Card Overview All devices on a computer net

CyberPower Remote Management System 30 If the response is shown as below, the IP address is in use. Try another IP address until an available addres

CyberPower Remote Management System 31 CyberPower Systems (USA), Inc. 4241 12th Avenue East, Suite 400, Shakopee, MN

CyberPower Remote Management System 2 Application Unpacking Inspect the Remote Management Card upon receipt. The package should co

CyberPower Remote Management System 3 INSTALLATION GUIDE Step 1. Hardware Installation Internal smart slot Remote Management Card 1. Turn off th

CyberPower Remote Management System 4 RMCARD303

CyberPower Remote Management System 5 Definitions for LED Indicators Link LED color Condition Off The Remote Management Card is not connected to t

CyberPower Remote Management System 6 Figure 2. The setting window. 6. To modify the IP Address, Subnet Mask or Gateway address, enter

CyberPower Remote Management System 7 Method 2: Using a command prompt 1. Obtain the MAC address from the label on the Remote Management Card rear